Surface hardener and water-repellent
  • Guard Hardener® W is a product for mineralising and treating efflorescence, saltpetre, friable materials damaged by intrusion of water, damp, frost...
  • Guard Hardener® W penetrates friable materials certainly to crystallise, harden and mineralise. Once treated, materials become more resistant to degradations. Guard Hardener® W can also be used as an anti-dusting treatment.
  • Guard Hardener® W also has excellent water-repellent properties that help to prevent main causes of degradation such as infiltrations, acid rains, erosion, freeze-thaw cycles, development of micro-organisms, saltpetre, efflorescences...
  • Guard Hardener® W is a non film-forming impregnation product. Substrates remain permeable to air and water vapour. It is completely colourless after application and does not change the appearance or the composition of the treated surface. It is also UV-resistant and does not discolor with age.
Guard Hardener® W can be used indoors and outdoors on facades, walls, roofings, floors, screeds and on all porous materials: cement, plaster, concrete, natural stone, brick, render...
  • Hardens and consolidates porous friable materials.
  • “Anti-dusting” action.
  • Protects against water, humidity and frost and thus limits development of efflorescence, moss and lichens.
  • 10 year efficiency.
  • Colourless.
  • Non film-forming, lets a surface breathe.
  • Water-based product, solvent-free and non flamable.
Apply using a low pressure sprayer, a brush or a roller.
Clean tools and equipment immediately after use with water.
  • Apply the product to a surface that is clean.
  • A mechanical cleaning with a brush or chemical cleaning can be done.
  • To remove stains and marks of pollution use Guard Cleaner® Polluted facades. In case of greasy stains use Guard Cleaner® Eco Soiled floors. For efflorescence or saltpetre use Guard Remover® Eco Efflorescence & cement.
  • Apply product neat – do not dilute.
  • Shake the product well before use. Always carry out a preliminary test.
  • Apply to the point of saturation of the substrate in 1 layer or in 2 layers «wet on wet» according to the porosity.
  • Do not overcharge the substrate – remove all excess before it dries. Risk of white stains in case of excess.
  • Full efficiency achieved after drying 2 to 7 days.
  • The treated substrate must not be covered by another coating.
  • Physical state at 20°C: Liquid.
  • Appearance: Uncoloured.
  • Odour: None.
  • pH: 13 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Density: 1.02 ± 0.01.
  • Solubility in water [vol/vol]: Total.
  • Flash point [°C]: Not applicable.
  • COV: < 1g/l.
The following values are for guidance only: 3 to 6m² / litre.
5 and 20 L can.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 24 months following the production date when kept in the original unopened container.
  • Always carry out preliminary tests to check the penetration of the product and the final look of the substrate.
  • On certain materials, Guard Hardener® W can change slightly the colour.
  • For ideal application and effective results, Guard Hardener® W must be used when the substrate temperature is between 5°C and 30°C.
  • Do not apply in rain or very hot weather. Air temperature between 5°C and 30°C.
  • Do not apply to waterlogged, organic, metallic, impermeable or low-porous materials.
  • Product is alkaline. Handle preferably with gloves and goggles. Protect painted surfaces, glass, tiles and light alloys (aluminium, chrome, copper, zinc, etc). Accidental splashes should be rinsed off immediately with water.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear rubber gloves resistant to chemical products.
  • Skin protection: No special protective clothing or skin protection is required under normal condi tions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN.
Chemical nature
Mixture of siliconate and silicate in an aqueous phase.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 62
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.610.402