Specialist
Solution
Product
Document
Picture

Water and oil repellent, anti-staining and anti-graffiti total protection for all porous building substrates
ProtectGuard® is the leading product for all-round protection for all porous building materials. This one product delivers water and oil repellent protection and anti-graffiti protection for porous building materials.
ProtectGuard® helps tackle the deterioration caused by atmospheric pollution, grease-type staining, penetration of liquids and graffiti. A surface treated with ProtectGuard® will benefit from an increased life-span and will be easier to maintain.
ProtectGuard® is a non film-forming impregnation product that leaves the treated surface permeable to air and water vapour.
ProtectGuard® is completely colourless after application and does not change the appearance or the composition of the treated surface. It is also UV-resistant and does not discolor with age.
ProtectGuard® may be used indoors or outside on walls, floors and roofing. It is designed to protect all porous building materials such as natural and synthetic stone, concrete, terracotta, cement, selflocking paving... On low porous materials, use ProtectGuard® HD or ProtectGuard® MG Eco. ProtectGuard® is used for new and renovated constructions.
  • Effective for more than 10 years demonstrated by the CEBTP (Experimental Centre for Research and Study in Construction and Public Works).
  • Protects against water, oily liquids and staining.
  • Limits efflorescence formation.
  • Anti-staining, anti-dirt.
  • Prevents chewing-gum from sticking, limits dirt due to pollution from building up again. Limits moss and lichen growth.
  • Makes cleaning easier.
  • Very good anti-graffiti properties.
  • Prevents deterioration resulting from freeze-thaw cycle.
  • Non film-forming, lets the surface breathe.
  • UV-resistant, does not discolour.
  • Invisible once dry.
  • Ready to use, easy to use.
Apply using a low pressure sprayer, a roller or a brush.
Clean tools and equipment immediately after use with water.
  • Apply the product to a surface that is clean, dust-free, grease-free and dry. To remove stains and marks of pollution use Guard Cleaner® Polluted Facades or Guard Wash®. In case of greasy stains use Guard Cleaner® Eco Soiled Floors. For efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement.
  • Rinse carefully and wait until the surface is completely free from any cleaner marks before applying ProtectGuard®.
  • Use neat, do not dilute.
  • Shake the product well before use.
  • Always carry out a preliminary test.
  • The treated surface should be impregnated to saturation point, either in one application or in two applications ‘wet-on-wet’.
  • Do not over apply, eliminate any exceeding product before drying.
  • On vertical surfaces, apply from the bottom-up.
  • Drying time: 24 hours.
  • Optimum effectiveness obtained after 7 days.
  • Physical state at 20°C: Liquid.
  • Appearence: Uncoloured.
  • Odour: None.
  • pH: 5.5 ± 0.5.
  • Boiling point [°C]: 100°C.
  • Density: 1.0 ± 0.01.
  • Solubility in water [vol/vol]: Total.
  • Flash point [°C]: Not applicable.
Coverage depends on the porosity of the material. The figures below should be used only as a general guideline:
* Calculation based on the components’ data.
1, 5 and 25 litres.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 24 months following the production date when kept in the original unopened container.
Stubborn dirt should be cleaned off with clean water or with a pH neutral cleaner...
Environment-friendly product:
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Non hazardous and non toxic.
  • 100% biodegradable*.
  • VOC < 2 g/l*.
  • 2008 Award of the “Éco Trophées 93”.
  • Remove all atmospheric pollution-related dirt from all surfaces to be treated before starting the treatment.
  • For best results it is essential that ProtectGuard® is used when the temperature of the substrates is between 5°C and 30°C.
  • Do not apply to low or very low porous materials. Depending on the porosity or the materials used ProtectGuard® HD, ProtectGuard® MG Eco or ProtectGuard® MG.
  • Do not apply to organic, metallic or waterproofing materials.
  • Do not apply during rain or in very hot weather. Air temperature between 5°C and 30°C.
  • Do not dilute or mix with any other product.
  • We recommend maintaining regularly the surface to keep its new look.
  • ProtectGuard® does not prevent from tire marks on floors. To remove these marks, use Guard Cleaner® Eco Soiled Floors.
  • Some stains (eg. stains from leaves) seem harder to remove. In this case, just apply some Guard Wash®, let it act and then rinse with water. It will not remove the protection product.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Chemical nature:
Water-borne fluorinated copolymer based.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 62
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.610.426
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other